What Is a Miami-Dade NOA? Impact Window & Door Approvals Explained

Updated October 30, 2026 · Written by the installation team at Vision Aluminum & Glass Specialists, licensed Florida contractor CGC 1537007

Quick answer

A Miami-Dade NOA (Notice of Acceptance) is the county’s approval for a specific building product, issued after the product passes testing for the High Velocity Hurricane Zone, including the large-missile impact test (TAS 201) and wind-pressure tests (TAS 202 and TAS 203). In Miami-Dade and Broward, replacement windows and doors must carry an approval valid for HVHZ use. Always get the NOA or Florida Product Approval number and check that it covers your exact product, size and installation.

What does an NOA actually approve?

An NOA is not a general stamp of quality. It approves one product line under specific conditions, and every condition matters on your house.

What the NOA specifiesWhy it matters
Product and seriesThe approval only covers the exact product named
Maximum sizesA window larger than the tested size is not covered
Design pressuresThe positive and negative wind pressure the product is rated for
Glass makeupThe laminated glass construction that was tested
Installation and anchoringThe fasteners, spacing and substrate the product must be installed with
Expiration dateEach approval has a validity period — it must be current

Why do Miami-Dade and Broward require it?

Both counties are in the High Velocity Hurricane Zone defined by the Florida Building Code — the strictest wind standard in the United States. Products installed there must be approved for HVHZ use, which is why the NOA, or a Florida Product Approval that specifically covers HVHZ use, appears on every window and door permit. Palm Beach County is outside the HVHZ but inside the wind-borne debris region, so impact protection is still required there under a Florida Product Approval. See our Miami-Dade and Broward pages for local permit details.

NOA vs. Florida Product Approval

Miami-Dade NOAFlorida Product Approval
Issued byMiami-Dade County Product ControlFlorida Building Commission
Used inMiami-Dade and Broward (HVHZ)Statewide; valid in the HVHZ only when approved for HVHZ use
Where to look it upMiami-Dade County’s product control recordsfloridabuilding.org

What tests are behind an HVHZ approval?

The best known is TAS 201, the large-missile impact test, in which a 9-pound piece of 2×4 lumber is fired at the product at 50 feet per second to simulate debris in a hurricane. The product must then survive the wind-pressure testing defined in TAS 202 and TAS 203, which apply static and repeated cyclic pressure — positive and negative — like the gusts of a long storm. A product has to pass the whole sequence, not just the impact.

Want to see the approval for every window in your quote? Just ask.

Vision Aluminum & Glass Specialists — rated 4.9★ from 55 Google reviews. Licensed Florida contractor CGC 1537007, serving Miami-Dade, Broward and Palm Beach County since 2014. Free, no-obligation estimates.

Call (954) 350-2622WhatsApp usRequest an estimate online

How to verify the approval for your windows

  1. Ask your contractor for the NOA or Florida Product Approval number for every window and door in the quote.
  2. Look the number up: Miami-Dade product control records on miamidade.gov, or Florida approvals on floridabuilding.org.
  3. Confirm the approval is current and covers HVHZ use if you are in Miami-Dade or Broward.
  4. Check that your window sizes are within the maximum sizes listed.
  5. Check that the design pressure meets what your permit requires for each opening.
  6. After installation, confirm the product label is on the frame and the anchoring follows the approval.

Red flags to watch for

  • The contractor cannot give you an approval number, or says it is pending.
  • The number belongs to a different product series than the one being installed.
  • Windows are larger than the approval’s maximum size.
  • The glass is swapped for a cheaper makeup than the approval lists.
  • The installation skips the anchoring the approval requires, or there is no permit.

How we handle approvals

Every opening in our quotes is listed with its product and approval number. We size each window within its approval, follow the required anchoring, submit the approvals with the permit and meet the inspector at final inspection. The paperwork is also what your insurer’s wind mitigation inspector needs to verify your opening protection.

Frequently Asked Questions

Do I need a Miami-Dade NOA in Palm Beach County?

Not necessarily. Palm Beach County is outside the High Velocity Hurricane Zone, so a Florida Product Approval is used, but impact protection is still required there.

Do NOAs expire?

Yes. Each approval has a validity period, so check that the approval for your product is current.

Does Miami-Dade approved mean hurricane-proof?

No product is hurricane-proof. An approval means the product passed the county’s impact and wind-pressure tests and is rated for the design pressures listed in it.

Can I look up an NOA myself?

Yes. Approvals are public records. Ask for the number and look it up through Miami-Dade County’s product control records or on floridabuilding.org.

Related: Impact window replacement · Impact door installation · Window repair & installation · 2026 price guide

Ready for a free, measured quote?

Vision Aluminum & Glass Specialists — rated 4.9★ from 55 Google reviews. Licensed Florida contractor CGC 1537007, serving Miami-Dade, Broward and Palm Beach County since 2014. Free, no-obligation estimates.

Call (954) 350-2622WhatsApp usRequest an estimate online

Get Your Free Estimate

★ 4.9 from 55 Google reviews · Licensed CGC 1537007

No obligation · Free in-home consultation

Scroll to Top